Calcium Carbonate FIBCs for Repeat-Use Review
If you need a 90 × 90 × 125 cm calcium carbonate FIBC for repeated forklift handling, use the size to start the drawing and specify the duty separately. Relia’s same-size baffle listing is rated 1,000 kg at 5:1. Your request is a different design target of 1,500 kg and 6:1, with 5–7 proposed trips. Reuse release depends on the offered construction, closed-loop controls and written approval for your actual handling sequence.
- Listed geometry
- Buyer design target
- Reuse gate
Korean Order Target
Use 90 × 90 × 125 cm and ±5% as the requested dimensional target. Record 1,500 kg SWL, 6:1 as a requested safety factor and indoor storage as separate requirements.
Manufacturing checks for this specification
Relia’s catalog identifies tubular weaving, coating and sewn bag assembly. For fine CaCO₃, the proposal should identify base cloth GSM and coating add-on separately, seam type and any filler cord, thread and loop attachment, tare weight and exact liner status. Both tie spouts should be called out on the drawing with clear units and measurement conventions.
- 01Match the spouts
- 02Specify fabric and seams
- 03Review the complete duty
At 2–3 loaded lifts per trip and 5–7 trips, the buyer’s planning range is 10–21 loaded lifts. It is a trial input. Define an approved cleaning, inspection and retirement procedure with both teams. Agree whether repairs are permitted in writing. Require finished-design load evidence plus a separate application trial, and match Korean artwork and dimensional tolerance to the approved revision.
A Same-Size Product Reference
Our 90 × 90 × 125 cm baffle listing is a geometry reference rated at 1,000 kg and 5:1. A quotation for 1,500 kg needs a separate approved construction and supporting test scope.
Separate dimensions from repeat-use evidence
The 90 × 90 × 125 cm baffle listing has side-seam loops, dual spouts, virgin PP, 1,000 kg SWL and 5:1. Its listed MOQ is 500. The 90 × 90 × 120 cm printed tubular listing also shows 1,000 kg and 5:1, with cross-corner loops. Both are reference constructions for the buyer’s 1,500 kg proposal.
On the Korea drawing, confirm whether 60 × 60 cm is diameter by length or a flat measurement. Put the 5–7 trips and 2–3 loaded lifts per trip in the trial brief. Review design type, instructions, inspection and retirement criteria before approving the duty.
ISO 21898:2024 · FIBCA safe handling guidelines
Spout Measurements for Both Interfaces
Mark the requested 60 × 60 cm spouts on the drawing. Tell us whether these numbers describe diameter and length or another measurement convention, and include tie placement and unloading clearance.
Handling Cycles as a Test Input
Five to seven trips at two to three loaded lifts per trip imply about ten to twenty-one loaded lifts. That estimate defines part of your brief. Agree the test protocol, inspection and retirement conditions for the intended duty.
A Construction Schedule for the Quote
Ask us to itemize fabric GSM, coating, seam construction and finished bag mass against the offered drawing. Send powder characteristics and any existing dust or sifting observations so the seam proposal has a clear objective.
A specification that separates cloth from performance
Ask for a side-by-side construction schedule showing uncoated cloth GSM, coating add-on, loop material and seam type. Put bag tare and finished dimensions on the same revision. Relia has verified repeat-use models available for review. Ask us which model and report are closest to this powder and route, then check whether the proposed spouts, fill weight and use cycle fall within that model’s evidence. A change to the reference design may require additional verification.
Inspection and Repair Boundaries
Tell us which defects you currently see between trips. Agree retirement criteria before use. Any proposed repair needs a separate review of the approved configuration, procedure and supporting evidence.
Two-Side Korean Artwork
Send vector artwork for the red and blue Korean text. Identify each panel and reading direction on the drawing. Approve an artwork proof separately from the structural sample.
Evidence to keep with the order
Keep the accepted drawing, product and powder description, operating sequence and sample test report under one revision. A 6:1 entry is a design requirement. The reuse decision also needs the agreed handling, inspection, cleanout and retirement limits. Obtain written approval for any change in spouts, liner, seams or handling duty.
FIBCA guidance on closed-loop reuse
Evidence for Purchase Approval
Request the report scope for the exact offered bag and the proposed cycle review. Ask the quote to separate sample costs, MOQ, lead time, monthly capacity and verified export references if available.
Send Your Powder Bag RFQ
Put the required 1,500 kg design, tie spouts and requested repeat-use duty on one RFQ line. Ask for explicit confirmation of all departures.
Contact the Relia Team
Send powder grade, bulk density, both spout drawings, forklift handling cycle, indoor storage conditions and blue/red artwork. Request the offered GSM, coating, tare, sample cost, MOQ, lead time, monthly capacity for this design and the exact-design test scope.
Qingdao, Shandong, China